MODELLING OF STRAIN HARDENING OF DUAL PHASE STEELS
DOI:
https://doi.org/10.66411/jer.v32i.21Keywords:
Constitutive Equations, Tensile Strength, Strain-Hardening, Dual Phase Steels, Plastic Deformation, Necking InstabilityAbstract
The strain hardening behaviors of dual phase steel with different volume fraction were studied using empirical models. The applicability of Log-method in describing the true stress-true plastic strain of dual phase steels was investigated. The tensile test data were analyzed by Hollomon equation and the results showed that the equation was not applicable for total plastic deformation stage.
The root-mean-square of residual percentage (RMSRP) was calculated for the curves obtained by regression formulae. The values of the Log-method parameters obtained by regression formulae were in good agreement with the experimental data.
It was found that increasing the volume fraction of martensite has a noticeable effect on the value of true strain at necking instability , when Log-method model is used. On the other hand, by using Hollomon model, the value of true strain at necking instability was moderately increased by increasing the volume fraction of martensite.
References
[1] J. H. Hollomon, The effect of heat treatment and carbon content on the work hardening characteristics of several steels”, Trans. Amer. Soc. Metals”,32, (1944) pp123-133.
[2] P. Ludwik; “Element der Technologischen mechanik”, J. Springer, Berlin, 32 (1909). DOI: https://doi.org/10.1007/978-3-662-40293-1
[3] H. W Swift: “Plastic Instability under plain stress”, J. Mech. Phys. Solids”,1, (1952) pp. 1-18. DOI: https://doi.org/10.1016/0022-5096(52)90002-1
[4] A. Kumar, S.B. Singh, K.K. Ray “Influence of Bainite/Martensite-Content on The Tensile Properties of Low Carbon Dual-Phase Steels” Materials Science Engineering A 474 (2008) 270-282 DOI: https://doi.org/10.1016/j.msea.2007.05.007
[5] X. Zuo, Y. Chen, M. Wang, “Study on Microstructures and Work Hardening Behavior of Ferrite-Martensite Dual-Phase Steels with High-Content Martensite” Materials Research. 15(2012) 915-921 DOI: https://doi.org/10.1590/S1516-14392012005000118
[6] E. N. Birgani and M. Pouranvari “Effect of Martensite Volume Fraction on the Work Hardeningn Behavior of Dual Phase Steels” Hradec nad Moravicí. 5 (2008) 19-21, (Metal 2009)
[7] O. Abedinia, M. Behroozia, P. Marashia, E. Ranjbarnodeha, M. Pouranvarib “Intercritical Heat Treatment Temperature Dependence of Mechanical Properties and Corrosion Resistance of Dual Phase Steel” Materials Research. 22 (2019) 1-10 DOI: https://doi.org/10.1590/1980-5373-mr-2017-0969
[8] H. Lorusso, A. Burgueño, D. Egidi and H. Svoboda, “Application of dual phase steels in wires for reinforcement of concrete structures” Procedia Materials Science, 1 (2012) 118-125. DOI: https://doi.org/10.1016/j.mspro.2012.06.016
[9] Y. Mazaheri, A. Kermanpur, and A. Najafizadeh; “Microstructures, Mechanical Properties, and Strain Hardening Behavior of an Ultrahigh Strength Dual Phase Steel Developed by Intercritical Annealing of Cold-Rolled Ferrite/Martensite, Metallurgical and Materials Transactions A, 46A, (2015) 3052 DOI: https://doi.org/10.1007/s11661-015-2918-0
[10] Z. Jiang, J, Lian, and J. Chen, “Strain hardening behavior and its relationship to tensile mechanical properties of dual phase steel”, Materials Science and Technology, 8 (1992)1075-1081 DOI: https://doi.org/10.1179/mst.1992.8.12.1075
[11] I. S. Yasnikov, A. Vinogradov, and Y. Estrin; “Revisiting the Considere criterion from the viewpoint of dislocation theory fundamentals” Scripta Materialia 76 (2014) 37–40 DOI: https://doi.org/10.1016/j.scriptamat.2013.12.009
[12] S. Kuang, Y. Kang, H. Yu and R. Liu, “Stress-strain partitioning analysis of constituent phases in dual phase steel based on the modified law of mixture” International Journal of Minerals, Metallurgy and Materials Volume 16, Number 4, August 2009, Page 393 DOI: https://doi.org/10.1016/S1674-4799(09)60070-4
[13] Y. T. Zhu, X.L. Wu, “Ductility and plasticity of nanostructured metals: differences and Issues” Materials Today Nano 2 (2018) 15-20 DOI: https://doi.org/10.1016/j.mtnano.2018.09.004
[14] M. Meyers and K. Chawla “Mechanical Behavior of Materials, Cambridge University Press, 2nd Edition, 2009, 171
[15] R. K. Nutor, N. K. Adomako, Y. Z. Fang” Using the Hollomon Model to Predict Strain-Hardening in Metals” American Journal of Materials Synthesis and Processing 2(1): (2017); 1-4. DOI: https://doi.org/10.11648/j.ajmsp.20170201.11
[16] M. R. Akbarpour, A Ekrami, “Effect of ferrite volume fraction on work hardening behavior of high bainite dual phase (DP) steels” Materials Science and Engineering: A 477 (1-2), (2008) 306-310. DOI: https://doi.org/10.1016/j.msea.2007.05.051
[17] M. M. Karimi, Sh. Kheirandish, U. U. Gomes, “Study on Work Hardening Behavior of Ferritic-Bainitic Dual Phase Steels” 22 CBECiMat Congresso Brasileiro de Engenharia e Ciência dos Materiais 06 a 10 de Novembro de 2016, Natal, RN, Brasil
[18] A. A. Abdulwahed, K. Z. Saleeb, K. Rozniatowski and K. J. Kurzydlowski “Extending the Log-Method Flow Equation to Stainless Steel Type 316 of Various Structures” Journal of Basic and Applied Sciences, Volume 15, Issue No. 1 (2005) Page 225-236
[19] ASTM E8-82, 1982 Annual book of ASTM Standards part 10, ASTM, Philadelphia, 1982, 119-139.
[20] N. Osman, Z. Sajuria, I. F. Mohameda, M. Z. Omara and S. Junaidi, “Effect of Intercritical Annealing on the Microstructural and Mechanical Behaviors of Dual-Phase Steels” Jurnal Kejuruteraan 32(4) 2020: 629-636 DOI: https://doi.org/10.17576/jkukm-2020-32(4)-10
[21] A. A. Abdulwahed, Krzysztof Rozniatowski and Krzysztof J. Kurzydlowski “Influence of Martensite Content on Tensile Properties of Dual-Phase Steel” Journal of Engineering Research (Al-Fateh University), Issue (11), March, 2009, pp 69-78 DOI: https://doi.org/10.66411/jer.v11i.185
[22] J. L. Devore; "Probability and Statistics for Engineering, and the Science"5th edition Duxbury Thomson Learning, (2000) pp.562.
[23] V. Colla, M. Desanctis, A. Dimatteo, G. Lovicu, “A. Solina, and R. Valentini “Strain Hardening Behavior of Dual-Phase Steels” Metallurgical and Materials Transactions A November 2009 DOI: https://doi.org/10.1007/s11661-009-9975-1
[24] H. P. Shen, T.C. Lei, and J.Z. Liu; “Microscopic deformation behavior of martensitic-ferritic dual-phase steels”, Materials Science and Technology, Vol.2, (1986), 28 DOI: https://doi.org/10.1179/mst.1986.2.1.28
[25] K. Park, M. Nishiyama, N. Nakada, T. Tsuchiyama, S. Takaki; “Effect of the martensite distribution on the strain hardening and ductile fracture behaviors in dual-phase steel”, Materials Science and Engineering A 604 (2014) 135–141 DOI: https://doi.org/10.1016/j.msea.2014.02.058
[26] M. Nouroozi, H. Mirzadeh, M. Zamani; “Effect of microstructural refinement and intercritical annealing time on mechanical properties of high-formability dual phase steel”, Materials Science & Engineering A 736 (2018) 22–26 DOI: https://doi.org/10.1016/j.msea.2018.08.088
[27] D. A. Korzekwa, D. K. Matlock, and G. Krauss, “Dislocation substructure as a function of strain in a dual-phase steel”, Metall. Trans, A 15(1984):1221–28 DOI: https://doi.org/10.1007/BF02644716
Downloads
Published
Issue
Section
License
Copyright (c) 2021 Journal of Engineering Research (Libya)

This work is licensed under a Creative Commons Attribution 4.0 International License.
