CFD-MODELLING AND THERMAL CHARACTERIZATION OF FRICTION STIR WELDING USING TOOL WITH POLYGONAL PINS

Authors

  • Esam Hamza Libyan Authority for Scientific Research, Tripoli, Libya Author

DOI:

https://doi.org/10.66411/jer.v32i.22

Keywords:

Friction Stir Welding (FSW), Analytical Approaches, Dynamic Mesh, Computational Fluid Dynamics (CFD), Liquid Fraction

Abstract

in the last two decades, Friction Stir Welding (FSW) has shown a capability to produce high strength joints particularly for the materials that cannot be welded by the conventional welding processes. Hence, optimizing the FSW process parameters to improve the quality of welded joint is still a subject of active research. In view of that, the efficient control of the welding thermal cycle through the geometrical and operational parameters may lead to produce sound weldments where defects can be avoided. Various studies have been carried out considering different tool pin profiles to improve the mechanical strength of welded joint, but the influences of the polygonal pin profiles on the thermal characterizations have been rarely reported in details. Besides, the experimental work has often showed that it is cost and time consuming particularly when the effect of geometrical variables is investigated. The present work focuses on the integral employment of analytical approaches and Computational Fluid Dynamics (CFD) tool to simulate the heat generation and the thermal field associated to the FSW when using tool with polygonal pins. A three-dimensional CFD model considering both dynamic mesh and sliding mesh techniques has been used to investigate the effect of a wide range of geometrical and operational parameters on the temperature distribution and peak temperature within thick FS welded workpieces. A set of novel analytical formulas have been developed to calculate the amount of heat generation corresponding to the pin shape. 

255 140

References

[1] Gibson, B. T., Lammlein, D. H., Prater, T. J., Longhurst, W. R., Cox, C. D., Ballun, M. C., and Strauss, A. M. (2014). Friction stir welding: Process, automation, and control. Journal of Manufacturing Processes, 16(1), 56-73.‏

[2] Mishra, R.S., P.S. De, and N. Kumar, Friction Stir Welding and Processing. Science and Engineering. 2014, Dordrecht: Springer International Publishing.

[3] Schmidt, H., Hattel, J., & Wert, J. (2003). An analytical model for the heat generation in friction stir welding. Modelling and simulation in materials science and engineering, 12(1), 143.‏

[4] Mehta, M., Reddy, G. M., Rao, A. V., & De, A. (2015). Numerical modeling of friction stir welding using the tools with polygonal pins. Defence Technology, 11(3), 229-236.‏

[5] Mehta, M., De, A., & DebRoy, T. (2014). Material adhesion and stresses on friction stir welding tool pins. Science and Technology of Welding and Joining, 19(6), 534-540.‏

[6] Darmadi, D. B., & Talice, M. (2020). Improving the strength of friction stir welded joint by double side friction welding and varying pin geometry. Engineering Science and Technology, an International Journal.‏ 24(3), 637-647

[7] Fujii, H., Cui, L., Maeda, M., & Nogi, K. (2006). Effect of tool shape on mechanical properties and microstructure of friction stir welded aluminum alloys. Materials Science and Engineering: A, 419(1-2), 25-31.‏

[8] Elangovan, K., & Balasubramanian, V. (2007). Influences of pin profile and rotational speed of the tool on the formation of friction stir processing zone in AA2219 aluminium alloy. Materials Science and Engineering: A, 459(1-2), 7-18.

[9] Elangovan, K., Balasubramanian, V., & Valliappan, M. (2008). Influences of tool pin profile and axial force on the formation of ‏ friction stir processing zone in AA6061 aluminium alloy. The international journal of advanced manufacturing technology, 38(3-4), 285-295.‏

[10] Elangovan, K., & Balasubramanian, V. (2008). Influences of tool pin profile and tool shoulder diameter on the formation of friction stir processing zone in AA6061 aluminium alloy. Materials & design, 29(2), 362-373

[11] Gharaibeh, N., Al-Jarrah, J. A., & Sawalha, S. A. (2016). Effect of pin profile on mechanical properties of 6061 al alloy welded joints prepared by friction stir welding. Triangle, 11(96.16), 1-42.‏.‏

[12] Biswas, P., A Kumar, D., & Mandal, N. R. (2012). Friction stir welding of aluminum alloy with varying tool geometry and process parameters. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 226(4), 641-648.‏

[13] Vijay, S. J., & Murugan, N. (2010). Influence of tool pin profile on the metallurgical and mechanical properties of friction stir welded Al–10 wt.% TiB2 metal matrix composite. Materials & Design, 31(7), 3585-3589.‏

[14] Gopalakrishnan, S., & Murugan, N. (2011). Prediction of tensile strength of friction stir welded aluminium matrix TiCp particulate reinforced composite. Materials & Design, 32(1), 462-467.‏

[15] Palanivel, R., Mathews, P. K., Murugan, N., & Dinaharan, I. (2012). Effect of tool rotational speed and pin profile on microstructure and tensile strength of dissimilar friction stir welded AA5083-H111 and AA6351-T6 aluminum alloys. Materials & Design, 40, 7-16.‏

[16] Vijayan, D., & Rao, V. S. (2014). A Multi Response Optimization of Tool Pin Profile on the Tensile Behavior of Age-hardenable Aluminum Alloys during Friction Stir Welding. Research Journal of Applied Sciences, Engineering and Technology, 7(21), 4503-4518.‏

[17] Patel, V. V., Badheka, V., & Kumar, A. (2017). Effect of polygonal pin profiles on friction stir processed superplasticity of AA7075 alloy. Journal of materials processing technology, 240, 68-76.‏

[18] Mugada, K. K., & Adepu, K. (2019). Effect of knurling shoulder design with polygonal pins on material flow and mechanical properties during friction stir welding of Al–Mg–Si alloy. Transactions of Nonferrous Metals Society of China, 29(11), 2281-2289.‏

[19] Buffa, G., Hua, J., Shivpuri, R., & Fratini, L. (2006). Design of the friction stir welding tool using the continuum based FEM model. Materials Science and Engineering: A, 419(1-2), 381-388.‏

[20] Patel, J. B., & Patil, H. S. (2014). Simulation of peak temperature & flow stress during FSW of aluminium alloy AA6061 for various tool pin profiles. Int J Mater Sci Eng, 2(1), 67-71.‏

[21] Marzbanrad, J., Akbari, M., Asadi, P., & Safaee, S. (2014). Characterization of the influence of tool pin profile on microstructural and mechanical properties of friction stir welding. Metallurgical and Materials Transactions B, 45(5), 1887-1894.

[22] ‏Su, H., Wu, C. S., Bachmann, M., & Rethmeier, M. (2015). Numerical modeling for the effect of pin profiles on thermal and material flow characteristics in friction stir welding. Materials & Design, 77, 114-125.

[23] Ulysse, P. (2002). Three-dimensional modeling of the friction stir-welding process. International Journal of Machine Tools and Manufacture, 42(14), 1549-1557.‏ ‏

[24] Colegrove, P. A., & Shercliff, H. R. (2005). 3-Dimensional CFD modelling of flow round a threaded friction stir welding tool profile. Journal of materials processing technology, 169(2), 320-327.‏

[25] Crawford, R., Cook, G. E., Strauss, A. M., & Hartman, D. A. (2006). Modelling of friction stir welding for robotic implementation. International Journal of Modelling, Identification and Control, 1(2), 101-106.‏

[26] Nandan, R., Roy, G. G., Lienert, T. J., & DebRoy, T. (2006). Numerical modelling of 3D plastic flow and heat transfer during friction stir welding of stainless steel. Science and Technology of Welding and Joining, 11(5), 526-537.‏

[27] Atharifar, H., Lin, D., & Kovacevic, R. (2009). Numerical and experimental investigations on the loads carried by the tool during friction stir welding. Journal of Materials Engineering and Performance, 18(4), 339-350.‏

[28] Aljoaba, S. Z., Jawahir, I. S., Dillon, O. W., Ali, M. H., & Khraisheh, M. K. (2009). Modeling of friction stir processing using 3D CFD analysis. International journal of material forming, 2(1), 315-318.‏

[29] Lin, S. B., Zhao, Y. H., He, Z. Q., & Wu, L. (2011). Modeling of friction stir welding process for tools design. Frontiers of Materials Science, 5(2), 236-245.‏

[30] Yu, Z., Zhang, W., Choo, H., & Feng, Z. (2012). Transient heat and material flow modeling of friction stir processing of magnesium alloy using threaded tool. Metallurgical and Materials Transactions A, 43(2), 724-737.‏

[31] Mohanty, H., Mahapatra, M. M., Kumar, P., Biswas, P., & Mandal, N. R. (2012). Study on the effect of tool profiles on temperature distribution and material flow characteristics in friction stir welding. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 226(9), 1527-1535.‏

[32] WU, C. S., ZHANG, W. B., Lei, S. H. I., & CHEN, M. A. (2012). Visualization and simulation of plastic material flow in friction stir welding of 2024 aluminium alloy plates. Transactions of Nonferrous Metals Society of China, 22(6), 1445-1451.‏

[33] Chen, G. Q., Shi, Q. Y., Li, Y. J., Sun, Y. J., Dai, Q. L., Jia, J. Y., ... & Wu, J. J. (2013). Computational fluid dynamics studies on heat generation during friction stir welding of aluminum alloy. Computational Materials Science, 79, 540-546.

[34] Ji, S., Xing, J., Yue, Y., Ma, Y., Zhang, L., & Gao, S. (2013). Design of friction stir welding tool for avoiding root flaws. Materials, 6(12), 5870-5877.‏ ‏

[35] Cho, H. H., Hong, S. T., Roh, J. H., Choi, H. S., Kang, S. H., Steel, R. J., & Han, H. N. (2013). Three-dimensional numerical and experimental investigation on friction stir welding processes of ferritic stainless steel. Acta Materialia, 61(7), 2649-2661.‏

[36] Chen, G. Q., Shi, Q. Y., Fujiya, Y., & Horie, T. (2014). Simulation of metal flow during friction stir welding based on the model of interactive force between tool and material. Journal of materials engineering and performance, 23(4), 1321-1328.‏

[37] Kang, S. W., Jang, B. S., & Kim, J. W. (2014). A study on heat-flow analysis of friction stir welding on a rotation affected zone. Journal of mechanical science and technology, 28(9), 3873-3883.

[38] Zhang, Z., & Wu, Q. (2015). Analytical and numerical studies of fatigue stresses in friction stir welding. The International Journal of Advanced Manufacturing Technology, 78(9-12), 1371-1380.‏

[39] Kadian, A. K., & Biswas, P. (2015). A comparative study of material flow behavior in friction stir welding using laminar and turbulent models. Journal of Materials Engineering and Performance, 24(10), 4119-4127.‏ ‏

[40] Gadakh, V. S., Kumar, A., & Patil, G. V. (2015). Analytical modeling of the friction stir welding process using different pin profiles. Welding Journal, 94(4), 115-124.‏

[41] Hamza, E., Asim, T., & Mishra, R. (2016). Computational Fluid Dynamics based Transient Thermal Analysis of Friction Stir Welding. 6th International and 43rd National Conference on Fluid Mechanics and Fluid Power (FMFP-2016). December 2016: Allahabad, India ‏

[42] Hamza, E. (2020). Dimensions Effect of the Rotating Fluid Zone on the Results when CFD Modeling of Friction Stir Welding.‏ Third Conference for Engineering Sciences and Technology (CEST-2020). 01-03 December 2020 /Alkhoms - Libya

[43] Nandan, R., Roy, G. G., & Debroy, T. (2006). Numerical simulation of three-dimensional heat transfer and plastic flow during friction stir welding. Metallurgical and materials transactions A, 37(4), 1247-1259.

[44] FLUENT online manual. Available from: http://www.ansys.com/products/fluiddynamics/. ‏

[45] Ansys 13.0.0 User Guide

[46] Mishra, R. S., & Ma, Z. Y. (2005). Friction stir welding and processing. Materials science and engineering: R: reports, 50(1-2), 1-78.‏

[47] Al-Abidi, A. A., Mat, S. B., Sopian, K., Sulaiman, M. Y., & Mohammed, A. T. (2013). CFD applications for latent heat thermal energy storage: a review. Renewable and sustainable energy reviews, 20, 353-363.‏

[48] Muhieddine, M., Canot, E., & March, R. (2009). Various approaches for solving problems in heat conduction with phase change. International Journal on Finite Volumes, 19.‏

[49] Gadakh, V. S., & Adepu, K. (2013). Heat generation model for taper cylindrical pin profile in FSW. Journal of Materials Research and Technology, 2(4), 370-375.‏

[50] Kang, S. W., & Jang, B. S. (2014). Comparison of friction stir welding heat transfer analysis methods and parametric study on unspecified input variables. Journal of Mechanical Science and Technology, 28(10), 4233-4246.‏

[51] Dudley, J. Selecting a Target Transient Time Step in a CFD Analysis. 2015 27 Mach; Available from: https://caeai.com/blog/selecting-target-transient-time-step-cfd-analysis.

[52] Radius of a regular polygon. Available from: http://www.mathopenref.com/polygonradius.html.

[53] Neto, D. M., & Neto, P. (2013). Numerical modeling of friction stir welding process: a literature review. The International Journal of Advanced Manufacturing Technology, 65(1-4), 115-126.‏

[54] Welding, E. B., & Handbook, A. S. M. (1993). Welding, brazing, and soldering. ASM Int, 6, 254.‏

[55] Colegrove, P. A., Shercliff, H. R., & Zettler, R. (2007). Model for predicting heat generation and temperature in friction stir welding from the material properties. Science and Technology of Welding and Joining, 12(4), 284-297.‏

Downloads

Published

30-09-2021

Issue

Section

Articles

How to Cite

[1]
E. Hamza, “CFD-MODELLING AND THERMAL CHARACTERIZATION OF FRICTION STIR WELDING USING TOOL WITH POLYGONAL PINS”, JER, vol. 32, pp. 43–78, Sep. 2021, doi: 10.66411/jer.v32i.22.

Most read articles by the same author(s)