PERFORMANCES OF METALLIC FOAMS AS SUPPORTS FOR CATALYSTS

Authors

  • Y. Swesi Chemical Engineering Department, Faculty of Engineering, University of Tripoli, Libya Laboratory of Catalytic Process Engineering Author
  • S. Mrayed Chemical Engineering Department, Faculty of Engineering , University of Tripoli, Libya Laboratory of Catalytic Process Engineering, Author
  • V. Meille University of Lyon, CNRS-CPE, 43 bd du 11 November 1918, BP 82077, 69616 Villeurbanne, France Author
  • I. Pitault University of Lyon, CNRS-CPE, 43 bd du 11 November 1918, BP 82077, 69616 Villeurbanne, France Author
  • S. AL Garyani Chemical Engineering Department, Faculty of Engineering , University of Tripoli, Libya Laboratory of Catalytic Process Engineering, Author

DOI:

https://doi.org/10.66411/jer.v18i.257

Keywords:

Foams, Packed Bed, Catalyst, Supporters, Pressure drop.

Abstract

Two types of catalytic foams-filled metallic and ceramic reactors having different pore sizes were investigated and compared with fixed bed reactors in order to observe the thermal effects and try to identify the key parameters that promote both heat and mass  transfer.  The  performance  of foam-filled  reactor  with  conventional  fixed  bed reactor   was   examined   using    an   endothermic  reaction.    The   reaction   was  the dehydrogenation of mehtylcyclohexan (MCH) to toluene on 2% Pt/γ -Al2O3, which is considered to be suitable reaction used to produce hydrogen for fuel-cell application. It was found that, for endothermic reactions not limited by external transport, the coated foams significantly increased the effective conductivity of catalytic beds, the denser foam  leading  to  higher  effective  conductivity.  The  results  indicate  a much higher pressure drop of the beads (ΔP with cata= 1600 Pa.m-1  at u = 0.92 m.s-1) compared to that of the different foams ( ΔP with cata= 476 Pa.m-1  at u = 0.92 m.s-1), and the Innocenti et al. correlation agrees very well with experimental data compared with other correlations

202 86

References

[1] V. Tomasic, F. Jovic, Appl. Catal. A Gen. Volume 311, (2006).

[2] P.G. Menon, M.F.M. Zwinkels, E.M. Johansson, S.G. Jaras, Kinet. Catal. Volume 39 (1998).

[3] V. Meille, Appl. Catal. A Gen. Volume 315, (2006). DOI: https://doi.org/10.1016/j.apcata.2006.08.031

[4] Do Hyung Kim, Byung Yong Yu, Pil Ryung Cha, Woo Young Yoon, Ji Young Byun, Sang Hoon Kim, Surface and Coatings Technology, Volume 209, (2012).

[5] C. Hutter, A.Zenklusen , R.Lang , Ph.RudolfvonRohr , Chemical Engineering Science, Volume 66 , (2011). DOI: https://doi.org/10.1016/j.ces.2010.12.016

[6] C.Hutter, D.Buchi, V.Zuber, Ph. Rudolf von Rohr, Chemical Engineering Science Volume 66, (2011).

[7] C C. Hutter, D.Buchi,V.Zuber, Ph.RudolfvonRohr, Chemical Engineering Science Volume 66, (2011). DOI: https://doi.org/10.1016/j.ces.2011.05.005

[8] J G. Fourie, J P. Du Plessis, Chemical Engineering Science, Volume 57, (2002). DOI: https://doi.org/10.1016/S0009-2509(02)00166-5

[9] J.T Richardson, Y Peng, D Remue, Applied Catalysis A: General, Volume 204, (2000). DOI: https://doi.org/10.1016/S0926-860X(00)00508-1

[10] David Edouard, Maxime Lacroix, Cuong Pham Huu, Francis Luck Chemical Engineering Journal, Volume 144, (2008). DOI: https://doi.org/10.1016/j.cej.2008.06.007

[11] G. Incera Garrido, F.C. Patcas, S. Lang, B. Kraushaar-Czarnetzki, Chemical Engineering Science, Volume 63,(008).

[12] Maxime Lacroix, Patrick Nguyen, Daniel Schweich, Cuong Pham Huu, Sabine Savin- Poncet, David Edouard, Chemical Engineering Science, Volume 62, (2007). DOI: https://doi.org/10.1016/j.ces.2007.03.027

[13] Leonardo Giani, Cinzia Cristiani, Gianpiero Groppi, Enrico Tronconi, Applied Catalysis B: Environmental, Volume 62, (2006). DOI: https://doi.org/10.1016/j.apcatb.2005.07.003

[14] S. Ergun, A.A. Oring, Ind. Eng. Chem. Volume 41, (1949). DOI: https://doi.org/10.1021/ie50474a011

Downloads

Published

31-03-2013

Issue

Section

Articles

How to Cite

[1]
Y. Swesi, S. Mrayed, V. Meille, I. Pitault, and S. AL Garyani, “PERFORMANCES OF METALLIC FOAMS AS SUPPORTS FOR CATALYSTS”, JER, vol. 18, pp. 17–26, Mar. 2013, doi: 10.66411/jer.v18i.257.